1/64 Scale 10 SPOKE MUSCLE Real Riderz Wheels and Tires Set for Hot Wheelz

Description: Easy to install wheels like Real Riders with rubber tires for Hot Wheels or any 1/64 Scale Cars..1 Set is for 1 car.1 Wheel set includes 4 wheels, 4 tires, 2 axles..Sizes:Regular: 10.6mm x 5.5mmStaggered Thin: 10.6mm x 5.5mm and 12.75mm x 5.4mmStaggered: 10.6mm x 5.5mm and 12.75mm x 6.7mmStaggered Wide: 10.6mm x 5.5mm and 12.75mm x 6.7mmStaggered Wide Huge: 12.75mm x 6.7mm and 14.6mm x 7.4mmHuge: 14.6mm x 7.4mm.Note: May require custom axles for perfect fit._____________________________________________________________________________________________________________________HOW TO INSTALL: Drill method:1) Drill out base rivets with roughly a 9/64" drill bit.2) Take car apart.3) Pry open / remove base tabs holding in original wheel axles.---for plastic bases, you can easily pry them open with small flathead screwdriver, or just snap them off with blade/wire cutters.---for metal bases, you may be able to snap them off with wire cutters (careful as this will send the tab flying across the room!) if you cannot remove the tab entirely, you will need to use dremel disc to grind off the rest of tab. ---if you don't care about the stock wheels/axles, you can also just bend them out to easily cut the axle with wire cutters4) Replace wheels/axles---if the custom wheels don't fit because axle is too short/long, you will need to adjust custom axle sets, see below.5) Reassemble car.---If you didn't overdrill, the base might just snap back together, otherwise you will need to lay car on it's roof and add some super glue onto the posts where the rivets used to be, or use some epoxy putty.Optional: Lower car's ride height by sanding down the interior that holds the axles.No Drill method:1) Cut stock axles with wire cutter.---you may need to bend the axles down to have room to cut them2) Use custom axles: ---1. Bend axle pins about 10-15 Degrees with pliers---2. Insert bent pin into axle tube (if it won't go in, you've bent it too much, unbend a bit and try again, if it slides out too easily, bend it more)---3. Insert 1 wheel into axle tube---4. Feed axle tube with wheel through car's base---5. Insert another wheel into axle tube on the other side of car/axle---6. Insert bent axle pin into axle tube to lock in the wheels3) Adjust as needed.---if axle tube is too long: uninstall axle and trim with dremel disc and try again---if axle tube is too short (rare): pull out axle pins slightly---if there is play in the wheels, add spacers to fill in the gaps from wheel to base (you can make your own or use my 3D printed spacers for an easier time)Note: if you don't use drill to open car, you can't lower the car's ride height._______________________________________________________________________________________________________________________Want tires with tire letters? Use my Tire Letter decals and be sure to check out my other decals listings such as:-Bugatti Chiron-Mazda RX7-Nissan Skyline GTR R32 R34 R35-Nissan 300ZX-Subaru Pandem BRZ-Lamborghini Huracan, Centenario-Universal liveries_______________________________________________________________________________________________________________________HOW TO INSTALL: Drill method:1) Drill out base rivets with roughly a 9/64" drill bit.2) Take car apart.3) Pry open / remove base tabs holding in original wheel axles.---for plastic bases, you can easily pry them open with small flathead screwdriver, or just snap them off with blade/wire cutters.---for metal bases, you may be able to snap them off with wire cutters (careful as this will send the tab flying across the room!) if you cannot remove the tab entirely, you will need to use dremel disc to grind off the rest of tab. ---if you don't care about the stock wheels/axles, you can also just bend them out to easily cut the axle with wire cutters4) Replace wheels/axles---if the custom wheels don't fit because axle is too short/long, you will need to adjust custom axle sets, see below.5) Reassemble car.---If you didn't overdrill, the base might just snap back together, otherwise you will need to lay car on it's roof and add some super glue onto the posts where the rivets used to be, or use some epoxy putty.Optional: Lower car's ride height by sanding down the interior that holds the axles.No Drill method:1) Cut stock axles with wire cutter.---you may need to bend the axles down to have room to cut them2) Use custom axles: ---1. Bend axle pins about 10-15 Degrees with pliers---2. Insert bent pin into axle tube (if it won't go in, you've bent it too much, unbend a bit and try again, if it slides out too easily, bend it more)---3. Insert 1 wheel into axle tube---4. Feed axle tube with wheel through car's base---5. Insert another wheel into axle tube on the other side of car/axle---6. Insert bent axle pin into axle tube to lock in the wheels3) Adjust as needed.---if axle tube is too long: uninstall axle and trim with dremel disc and try again---if axle tube is too short (rare): pull out axle pins slightly---if there is play in the wheels, add spacers to fill in the gaps from wheel to base (you can make your own or use my 3D printed spacers for an easier time)Note: if you don't use drill to open car, you can't lower the car's ride height.-------------------------------------------------------------------------------------------------------------------------------------------------------------------------Be sure to check out my other listings such as:-Real Riders 1/64 Scale Wheels and Tires-Headlight and Taillight Decals-Universal Liveries-Universal Wraps-Carbon Fiber Wrap-Side View Mirrors-Spacers Any questions, feel free to ask!-------------------------------------------------------------------------------------------------------------------------------------------------------------------------SHIPPING INFO: First Class Package with tracking Flat rate shipping: Doesn't matter how many wheels/decals you buy!USA: $4.99 Canada: $9.99Worldwide: $12.99 If your total shipping cost is higher than above, click 'Request Total' in your cart so I can fix shipping cost. If not possible, no worries, i will refund any extra shipping costs paid for :)-------------------------------------------------------------------------------------------------------------------------------------------------------------------------Follow me on Social Media for updates on Restocks and New Releases!Any questions, feel free to ask :)

Price: 4.99 USD

Location: Bakersfield, California

End Time: 2023-11-04T19:13:43.000Z

Shipping Cost: 4.99 USD