48" 12 Outlets Hardwired Power Strip, H412VW

Description: EPS-1043G Item is shown in the first/main picture. Other pictures are for illustration purpose - to help understand the installation procedure, connectors are not included with order. H412VW-- 48" Hardwired Power Strip with 12 Outlets, White This hardwired type power strip is good for installation in your kitchen, garage for cabinet, rack, island, countertop and so on. It is not for normal wall outlets. There is no power cord and plug with this unit Features 48" (1.22m) Durable Metal Housing Power Strip, No Ears (Mounting Tabs on Both Ends), White 12 White US NEMA 5-15R Outlets, Vertical Outlet Orientation Hardwired without Power Cord for Mounting at Your Desired Location 6 Easily Punched off Knockouts on Each Side (Top, Bottom Cover, Both Sides and Ends) ETL Approved and Listed (Conforms to UL 5 and CAN/CSA C22.2 No. 62)Outlets 3.54" (90mm) apart, center to center Easy On/Off Back Cover for Wire Connection Wires Readily Striped for Easier Removal and Faster InstallationGreat Item for Contractors, Electric Engineers, Electricians, Installers as well as DIYers Specification Model #: H412VW Description: 48" 12-Outlet Hardwire Power Strip, White Measurement: L48" x W1.61" x H1.16" (1219 x 41 x 29.5mm) * USB Port: N/A Outlets: 12 Outlet Color: White Outlet Orientation: Vertical Receptacle Type: NEMA 5-15R Outlet Spacing: 3.54" / 90mm (center to center) Electrical Rating: 110-125V / 15A / 60Hz Full Load: 1875VA (Recommended Max Load 1440W) On/Off Switch: N/A Circuit Breaker: N/A Knockout Cord Exit: 6 (Top, Bottom Cover, Both Sides & Ends) Knockout Rim to End: Top/Bottom Cover/Both Sides: 1.87"/47.5mm Mounting on Back: Additional Mounting Holes Available Mounting Tabs: N/A Mounting Clips: Spring Steel Mounting Clips Included SAFETY WARNINGInstallation work of this unit must be done by a professional, a licensed electrician or an electric engineer.Never install this unit during a thunder storm.Switch off the power before you start installation work.This unit is for indoor use only.This unit is not intended for use in or around wet or potentially wet areas including, but not limited to, aquariums, saunas, showers and fountains.Risk of Electric Shock! INSTALLATION GUIDE Before installation, you may need to get a 3/4″ wire clamp connector and 3 wire connectors (also referred to as terminal connectors). Decide your wire gauge, and visit/shop your local hardware, electric supply or home improvement stores and ask assistance for what connectors you should get. minimum tools required: a fine to medium fine philips screw driver, and a pair of scissors, and a pair of mid size slip joint pliers Turn off electricity in the houseDecide where to place this Hardwired Power Strip unitChoose the knockout to be used for cord exit, then gently punch it off with the back of a screw driver or other tool handyUnscrew the back cover off the unit with a philips screw driverTake out the white/transparent plastic insulation sheet, and use a pair of scissors to cut a hole on it (about 3/4″ in diameter, or big enough for) WHERE the wires will run through. If the bottom knockout on the back cover is to be used for wire connection, a wire clamp connector may not be needed, thus, please ignore step 6, 7 and 9 belowPut on the 3/4″ wire clamp connector in place. Secure its installation by tightening the big ring screw (which is inside the casing, with the pair of slip joint pliersRun the wires through the wire clamp connector, from outside into the Unit. In case bottom knockout on the back cover is to be used for wire connection, please run the wires through the back cover first and then the plastic insulation sheet , now with the knockout coin punched off, from outside to insideMatch the colored wires and secure the wire connection with proper wire connectorsTighten the two pressure screws properly on the wire clamp connectorPlace the plastic insulation sheet back and screw the back cover onMount the unit: A) For unit with ears (mounting tabs on both ends): mount the unit through the ears with screws provided B) For unit without ears, place the unit where it is intended to be, mark where to install clips, secure the clips with screws provided. Then snap the unit in onto the clips C) For models without ears up to 24″, and models with ears above 30″, mounting holes on the back cover could be used to secure the unit (but a unit CANNOT be installed with such mounting holes if the unit is to be placed against a wall/cabinet on the side since the unit cannot be reinstalled onto the back cover). Then, please mount the back cover first and then carefully screw the unit onto the back coverTurn electricity back on, it is ready to go NOTE: * For installation purpose: The length of the power strip does not include ears, if any (mounting tabs – 0.67″/17mm on each end. For models with ears, 2 x 0.67″/17mm need to be added to the product description length, please check the above spec chart for details); the width does not include the size of screws (min. 0.06″/1.5mm on each side); the height does not include the receptacles (about 0.19″/4.9mm above the casing). If faster shipping method needed, please contact us for more accurate shipping rates. Please contact us for shipping rates to HI, AK, PR, APO/AFP/FPO/MPO, offshore islands and int'l destinations. Please click "View seller's other items" for more sizes of this kind of products and more items available in our eBay store, and if you could find more interesting items to bid/buy and ship together, there may be savings on the shipping.

Price: 43.99 USD

Location: Ontario, California

End Time: 2024-12-05T22:38:45.000Z

Shipping Cost: 32 USD