Penguin r/c - Fanatec Podium DD1 / DD2 Emergency Stop, Kill Switch, E-Stop

Description: PSFSS OverviewThe PSFSS Fanatec Safety Switch is designed for use with the Fanatec DD1 and DD2 Direct Drive wheel systems. This Emergency Stop style switch is user selectable to provide the traditional Fanatec Emergency Stop power cutoff (OR) it can be programmed to disable the Torque Key limiting the power of the unit to the Low Power mode when activated. When using the torque limiting setting, the PSFSS allows you to retain control of the vehicle but at a significantly reduced force level to aid in being able to keep the car on the track and out of the way.In addition to the Emergency Stop functions this unit provides a remote power button and status LED so that you no longer need to reach behind the Direct Drive unit for power. The PSFSS is fully compatible with the Torque Off feature introduced with the Fanatec Firmware V345.The design of the the PSFSS complements both the DD1 and DD2 units and is easily mounted using M5x10 screws with the integrated attachment points on the back of the unit. The dimentions of the PSFSS were chosen to complement use with 80/20 rigs and the optional mounting plate PSSM allows the switch to be mounted flush next to 40mm section, the PSFM allows for front mounting.NOTE: For DD2 Owners, This unit replaces the existing Emergency Stop unit and adds the Torque Limiting Functionality.(please see features for a complete listing of differences) Features:Feature:PSFSSPSFSSlcnote:M2.25 Aerospace Carbon Fiber Woven Plate (face and back)OXM2.0 G10 Black Fiberglass Plate (face and back)XOAluminum Emergency Stop SwitchOOeStop Integrated LED Power indicatorOOPower Button Surround MaterialAluminumPlasticTorque limit modeOOFanatec DD1 & DD2 CompatibilityOOStructural Black 3D Printed FrameOOM5 mounting provision (39.25mm distance)OO*80/20 compatible dimentions M91 x M37.75 x M39.555.75mm height (including e-Stop height)OO**Dual 50" Included RJ12 cables (silver + black)OO***Additional Required & Optional Parts: Nothing Required - PSFM or PSSM Mounting plate reccomended (see notes: *)Notes:(*) Mounting screws are not included. The PSFSS is best when securely mounted so it is recommended to use either a solid DIY mounting or to purchase eiather the PSFM front mount plate or the PSSM side mount plate.(**) The PSFSS is designed to be visually compatible with 80/20 40mm profile.(***) 50" RJ12 cables are included with the PSFSS. Both cables are required for connection and to have full device functionality as a Torqule limiting e-Stop Setup and Configuration:Connection:Connect the Included RJ12 cables to the E.STOP (black wire) and T.KEY (silver wire) locations on the PSFSSlc. Route wires together to the back of your Fanatec DD Unit and plug the Black Wire into the E.Stop location on the back of your unit. Remove the Torque Key from your DD if not already removed and plug the silver wire into the Torque Key location. Place original torque key in a location where it will not be lost as it is not needed for this set-up but may be needed in the future. NOTE: In order for the PSFSS to function, BOTH connections must be made to your wheel base if only one or the other is connected the PSFSS will not function fully.Setting the Emergency Stop Protocol:To activate Torque Limiting mode set the switch on the back of the unit to the LIMIT position. If you wish for the the standard action of the Emergency Stop to be used (Power "off" with activation), set the switch to the OFF location.Using the PSFFS Safety Switch:When you get into a situation where you feel that you need a reduction or removal of power (depending on your setting) press the Red Emergency stop button. To reset the button after use turn the button cap slightly to the right and it will disconnect and pop into pre-activation state. After reactivation you will either need to Power the Direct Drive Base back "on" or confirm you wish to have Hi-Torque mode enabled by selecting OK on your wheel (via wheel button or 90deg wheel turn).To turn the wheel base "on" press the power button momentarily. To turn "off" the wheel base, press and hold the power button for at least 1 second. With the Fanatec Driver V345 and beyond, Fanatec has added a Torque Off feature that can be acivated by momentarily pressing the power button while the wheel base is "on". This Torque off feature can be deactivated in the same manner as it was turned on.Further Instructions:More detailed instructions are included in the Instructions for the PSFSS.Please click here to download.

Price: 74.99 USD

Location: Anaheim, California

End Time: 2024-11-30T08:34:52.000Z

Shipping Cost: 13 USD